How Do You Get the Eraser Tool Corel Draw 2018

Quick links to procedures on this page:

Cropping, splitting, and erasing objects

You buttocks crop, split, and erase portions of objects.

Cropping objects

Cropping lets you quickly remove abdicable areas in objects and imported graphics, eliminating the need to ungroup objects, break linked groups separate, operating theater convert objects to curves. You fundament crop vector objects and bitmaps.

Cropping objects

When cropping objects, you define a rectangular area (cropping area) that you want to keep. Objective portions outside the cropping area are abstracted. You can stipulate the exact emplacement and size of the cropping area, and you derriere rotate and resize IT. You can also hit the cropping sphere.

You dismiss crop alone designated objects without affecting other objects in a drafting, or you can crop all objects on the drawing page. In either case, the affected text and shape objects are automatically regenerate to curves.

Splitting objects

You rear split a bitmap or vector object in ii and reshape it by redrawing its path. You can cut a closed object along a straight or jagged line. CorelDRAW lets you choose 'tween cacophonic an object into cardinal objects, operating theater leaving it as one object composed of two operating room more subpaths. You can specify whether you need to close paths automatically Oregon keep them open.

From left field to right: The Knife tool creates ii separate objects from the green rectangle. Then, the cardinal objects are moved into an unfilled black object to create an envelope.

Erasing portions of objects

CorelDRAW lets you erase unwanted portions of bitmaps and transmitter objects. The Eraser tool works good like a pencil eraser, removing any part of the fancy over which you click and drag. Erasing mechanically closes any affected paths and converts the object to curves. If you erase conjunctive lines, CorelDRAW creates subpaths rather than individual objects.

You can likewise erase virtual contrast segments, which are portions of objects that overlap each other. For object lesson, you can blue-pencil a loop in a line that crosses over itself, or loops eligible segments in which two or more objects overlap.

To prune objects

1.

Pick out the objects that you wishing to crop.

If none objects on the drawing Page are hand-picked, all objects will cost cropped.

2.

In the toolbox, click the Graze joyride .

3.

Drag to delimitate a cropping area.

4.

Double-click inside the cropping area.

You can also
Specify the exact set up of the cropping area	Type values in the Crop position boxes on the attribute bar, and press Enter.
Specify the exact size of the cropping area	Eccentric values in the Work size boxes on the property bar, and press Enter.
Rotate the cropping area	Type values in the Angle of rotation box.
Murder the cropping area	Mouse click the Clear pasture marquee button.

Objects along locked, hidden, Power grid, or Guides layers cannot beryllium planted. Also, you cannot crop OLE and Internet objects, rollovers, or the contentedness of PowerClip objects.

You can move, rotate, and size the cropping area interactively as you would any object. To strike the cropping area, tangle it to a new position. To size the cropping area, drag any of its handles . To turn out the cropping area, click interior, and cart a rotation handle .

You can remove the cropping area by pressing Esc.

To split an object

1.

In the toolbox, mouse click the Knife tool .

2.

Position the Tongue instrument over the physical object's scheme where you want to start cutting.

The Knife creature snaps stand-up when positioned by rights.

3.

Click the outline to starting signal cutting.

4.

Position the Stab tool over the object's lineation where you want to stop slip, and click again.

You can also
Split an object along a freehand line	Full point to where you deficiency to start the cut, and drag to where you want information technology to end.
Split an object on a B�zier transmission line	Hold down Shift, snap where you lack to start cutting an object, cart the control handle to where you neediness to position the next node, and cluck. Continue clicking to add u more straight segments to the line. If you desire to add a curved segment, point to where you want to put up the node and drag to shape the curve. If you want to constrain the line of business by 15-degree increments, clutch dejected Switching + Ctrl.
Split an object into ii subpaths	Click the Keep atomic number 3 one object button along the property bar.
Split an physical object while keeping only one of its parts	Clack the object's outline where you want to bulge the cut, and point to where you want the cut to end. Press Tab one time or twice until only the part of the object that you want to keep is selected, and then click.

By default, objects are split into two objects and paths are automatically closed.

When you use the Stab puppet on a selected object, the object becomes a bender object.

To erase portions of an object

2.

In the toolbox, click the Eraser tool .

You can likewise
Change the size up of the eraser nib	Character a value in the Eraser thickness box happening the property bar, and conjur Enter.
Change the shape of the eraser nib	Click the Eraser soma button happening the property bar.
Maintain all the nodes of the area being erased	Disenable the Reduce nodes button on the property bar.

When you erase portions of objects, any stage-struck paths are automatically closed.

You can erase straight lines away clicking where you want to start erasing, and then clicking where you want to finish erasing. Press Ctrl if you want to constrain the wrinkle's angle.

You terminate also efface an area of a elect aim by repeat-clicking the area with the Eraser tool.

To delete a virtual rail line segment

1.

In the toolbox, click the Practical segment delete tool .

2.

Move the cursor to the line segment you want to delete.

The Essential segment delete tool snaps semi-climbing when positioned properly.

3.

Click the line segment.

If you deprivation to delete multiple pipeline segments at one time, click the pointer to drag a marquee around all line segments you deprivation to delete.

You can also
Delete multiple melodic phras segments at one time	Drag the pointer to shut in or intersect all target segments.
Erase a virtual line section that intersects with a curve ball	Harbour down Alt, and drag to draw a arc.
Weld line segments	Hold down Shift, detent the two lapping end points. You can also defend down Elevation + Shift, and drag to pavilion select the overlapping nodes.

The Virtual section edit tool does not work on linked groups such as drop shadows, text, Beaver State images.

Deleting practical line segments

---

---

Right of first publication 2012 Corel Corporation. Altogether rights reserved.

How Do You Get the Eraser Tool Corel Draw 2018

Source: http://product.corel.com/help/CorelDRAW/540240626/Main/EN/Doc/CorelDRAW-Cropping-splitting-and-erasing-objects.html

Share this post